Monday, October 26, 2020
Atlas Biomechanics : Heel Lifts for Unequal Limb Length in Polio Patients
Sunday, October 25, 2020
Heel Lifts for Unequal Limb Length in Polio Patients
Polio patients usually have a short leg and or scoliosis that can be treated with a common in shoe heel lift. This leg length discrepancy is permanent. Polio patients commonly will have lower back pain, hip, knee, and ankle pain due to the unequal leg length (short leg). Medical providers can easily treat the patient’s discomfort with a simple shoe heel lift. Usually, a heel lift that is dispensed is about 1/4 the limb length discrepancy. The proper height depends on the patient’s comfort level and how long they have had the short limb.
In shoe heel lifts are placed on the short limb side underneath the shoe’s insole. This allows the heel lift to sit firmly at the bottom of the shoe. Optimum control and comfort to the patient is then achieved. In shoe heel lifts can be manufactured from cork and EVA/rubber blend. They come in different heights to correct the leg discrepancy.
Atlas Biomechanics produces in shoe heel lifts here in the USA from medical grade rubber/cork and eva/rubber. They come in heights of 1/8″ (3mm) heel lift, 1/4″ (6mm) heel lift, 3/8″ (9mm) heel lift and 1/2″ (12mm) heel lift. An adjustable heel lift, that allows the heel riser to properly fit the short leg is a common type for polio patients. The 1/4″ heel lift is our most popular short leg lift for polio patients.
Teri Green
About Atlas Biomechanics: We are a woman-owned sports medical manufacturer of heel lifts, foot pads, and heat mold orthotics.
Friday, October 23, 2020
Atlas Biomechanics : Hockey Skate Custom Orthotics ( Ice Skate Arch Sup...
Thursday, October 22, 2020
Hockey Skate Custom Orthotics ( Ice Skate Arch Supports ) and Gait Cycle
Custom orthotics in hockey ice skates are used to increase the stability of the ankle, foot and knee. In the foot, it especially controls the subtalar, midtarsal and ankle joints. If any of these joints are not in their most efficient joint positions, then the ice skater will not have the most effective skating power.
The typical ice skater’s lower extremities never goes through a complete gait cycle. A skater ideally should have limited foot mechanics between the midstance and the beginning of propulsion, with slight knee flexion during the entire contact phase. When initiating a turn, an hockey skater will maintain their control by directing the inside knee medially and transferring the load inward to the foot’s medial edge. By internally rotating the tibia, a closed kinetic chain pronation of the foot will occur, which transfers the pressure through the skate boot through the blade’s inside edge.
Higher level hockey skaters will have a more subtle dynamic and the reverse is true for the beginner. When a hockey ice skater has an over pronated or unstable foot structure, they may a harder time turning as the medial arch of the foot may collapse within the skate boot before the edging force can be transferred.
Some indications you may need a hockey ice skate orthotic arch support.
1. Foot and or Ankle pain or fatigue with ice skating.
2. Weak crossovers.
3. Difficulty making a turn.
4. Knee and or Low Back pain or fatigue while skating.
5. Chronic fatigue or pain directly after skating.
A hockey ice skate orthotic should allow greater control with turning and crossovers. Usually, persons with ice skate custom arch support orthotics notice longer stride length and more explosive leg power. Ice skate custom arch supports should be thin for ease of placement, 3/4 length for toe room, semi rigid for control and adjustable for modifications. The best place for a hockey orthotic is under the skate’s insole for comfort, control and proper placement.
A heat moldable, direct contact orthotic from Atlas Biomechanics achieves all the above goals. It is only 1.3mm thick, fabricated with just a hot water bath, heat gun or toaster oven. Duplicate a lab built custom orthotic in less than 10 minutes.
Some Benefits of Our Heat Moldable Orthotics
*3/4 semi rigid sport orthotic shell.
*12mm heel cup for added control
*Medium profile (Sport Orthotic) to fit in most ice skates, gym, and casual shoes.
*1.3 mm thin. *Completely heat moldable and reheat formable.
*Proprietary material used to ease of mold.
*Total custom contact fit.
Teri Green
About Atlas Biomechanics: We are a woman owned sports medical manufacturer of Heat Moldable Orthotics.
Saturday, October 17, 2020
Atlas Biomechanics : Cork Adjustable Heel Lift with built in Varus/Valg...
Cork Adjustable Heel Lift with built in Varus/Valgus Heel Wedge
Atlas Biomechanics has developed a total new type of heel lift. We manufacture the only cork adjustable heel lift with a varus or valgus heel wedge built into the device. This type of adjustable heel lift is more stabilizing to the short leg. We are the only ones producing such an in shoe heel lift.
Atlas Biomechanics Adjustable Heel Lift with varus or valgus heel wedge
*Three removable 3 mm (1/8 inch) rubber cork layers.
*Each layer is peelable to achieve the proper correction of limb length discrepancy.
*1/2 of the bottom layer can be peeled for varus or valgus correction.
The heel wedge part helps prevent pronation of the Subtalar Joint of the short limb.
Most short legs will have an inverted calcaneus, our heel lift brings the ground to the foot.
More stabilizing foundation to the short limb.
Rubber cork is durable, light weight and comfortable.
Easily fabricate either a Varus Heel Wedge or Valgus Heel Wedge.
Sizes: Small: women 4-7 Medium: women 8-10, men 7-9 Large: women 9-11, men 10-14
Teri Green
About Atlas Biomechanics: we are a woman owned sports medical manufacturer of Heel Lifts, Foot Pads and Heat Moldable Orthotics.



